Your Plumbing Crash Course: A Guide to Installing a Bathtub
Your Plumbing Crash Course: A Guide to Installing a Bathtub
Blog Article
We have stumbled upon the article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the internet and believe it made perfect sense to relate it with you here.
Mounting a bathtub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, and also sometimes, tiling abilities. Changing an old tub with a new one is additionally a moderately hard job. If the old bathtub is easily available, the task can move easily; if you have to open up a wall to eliminate the old tub as well as place the new tub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly require an assistant to leave the old bathtub and also set in the new one. Make certain you have actually certified on your own for the task and fit trying it. Rather than hiring a service provider to take control of a halfway-completed project, it is far better to consider using one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This short article will certainly assist you install a brand-new tub in your shower room if you have already gotten a new tub and don't need to change the arrangement of your previous water pipelines.
Your devices as well as material list ought to comprise the following:
Planning for the Installment
Firstly, the supporting structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to prevent stress on the tub.
Fit the adaptable tap adapters to the bottom of both taps making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water system. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the restricted accessibility that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a fabric ready for the remaining water that will come from the pipelines. When the supply pipelines have been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Before going on to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Using the two wooden boards under its feet, put the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be attained by examining the level as well as readjusting the feet on the tub up until the level checks out level.
To install faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water supply and also check all joints as well as brand-new pipework for leakages as well as tighten them if necessary. Fill up the bathtub and likewise examine the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait until the bathtub has actually been made use of at least once as this will settle it right into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap as well as the sink. Secure the tap in position with the manufacturer provided backnut. When the tap is securely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The former type must be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack an inflexible seal, creating the water to pass through the wall surface between the bath as well as the tiling, causing problems with dampness and also feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as fittings. They are sold in tubes and also cartridges, and are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to enable the movement experienced when the bathtub remains in use. The sealant can fracture fairly early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently readily available on the market. It is suggested to fit the floor tiles making use of waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about How to Install a Bathtub? Post a short review down the page. We would be pleased to know your ideas about this posting. Hoping to see you back again soon. Loved our write-up? Please share it. Let someone else check it out. Thanks a lot for your time. Visit us again soon.
Immediate care? Call! Report this page